Quick Answer: Before you assume a Bosch refrigerator ice maker has failed, check that ice production is actually switched on. Bosch’s own manuals say Vacation mode and Sabbath mode both switch off ice production, and Sabbath only ends by itself after about 80 hours. Then check that the ice bin is fully inserted and aligned, the water pressure is at least 29 psi (Bosch’s range is 29-116 psi), and a water filter or bypass cap is in place, because Bosch says the water system won’t work without one. A new install needs about 4 hours for the first batch and up to 48 hours to fill the bin. Bosch’s reset for a real fault is to switch ice off, unplug the fridge for 5 minutes, and switch it back on. No CPSC recall exists for any Bosch refrigerator ice maker.
This guide covers the ice makers built into Bosch refrigerators: the 500 and 800 Series French-door models, the Benchmark built-ins and the bottom-freezer models. Bosch doesn’t sell a standalone countertop ice maker, as our Bosch ice maker guide explains. Everything below is based on Bosch’s US use-and-care manuals, its support and error-code pages, its parts store and the CPSC recall database. We don’t test appliances ourselves.
Diagnose your symptom
| What you see | Most likely cause (per Bosch's manuals) | Fix |
|---|---|---|
| No ice at all, display looks normal | Ice production switched off, or Vacation/Sabbath mode on | Switch ice production on; turn off Vacation or Sabbath mode |
| "lock" and "light" flash (500 Series dispenser) | Ice cube production is switched off | Hold lock + light until the light bar fills |
| Brand new, no ice yet | First batch takes about 4 hours after the freezer is cold | Wait; the bin can take up to 48 hours to fill |
| Ice stopped after a filter change or filter removal | No filter or bypass cap installed, or filter not seated | Seat a filter or the bypass cap fully |
| Small cubes or low output | Water pressure under 29 psi, often a reverse-osmosis system, or a blocked filter | Check the supply pressure; replace a filter older than 6 months |
| Production stops before the bin is full | Bin not fully inserted, or food or the ice scoop blocking the fill-level sensor | Reseat the bin; clear the sensor; don't leave the scoop on the ice |
| Makes ice but won't dispense | Cubes frozen together in the ice chute, bin not inserted, or keylock on | Clear the chute with a wooden spoon; reseat the bin; unlock |
| E02 on the display | Icemaker fault or ice/water control communication issue | Reset power at the breaker for 30 seconds |
| Still nothing after all of the above | Ice maker, water valve or control fault | 5-minute power reset, then Bosch service |
Which Bosch do you have? The ice maker differs by family
Bosch uses different controls and ice makers across its lineup, so start by matching your model number (on the label inside the fresh-food compartment) to its family. Ratings below are from Bosch’s US product pages.
| Family (example models) | How ice production is switched on/off | Rated ice per 24 h | Ice bin | Ice maker part (dealer fit lists) |
|---|---|---|---|---|
| 800 Series counter-depth, internal water dispenser (B36CT80SNS, B36CL80ENS) | Lift the ice maker cover in the freezer drawer and press the ice maker button; lit = on | 3.5 lb | 9 lb | 12028493 |
| 500 Series with external ice and water dispenser (B36CD50SNS, B36FD50SNS) | Hold "lock" + "light" together until the light bar lights fully | Up to 12 lb (QuickIce Pro) | 3 lb | 11036056 |
| Benchmark built-in (B36BT935NS, B36IT900NP) | Settings menu: "Ice cube production" | 2.9-3 lb | 7 lb | Check by model and E-Nr |
| Bottom-freezer with ice maker (B11CB81SSS) | Mechanical I/0 switch on the ice maker | 2.6 lb | 4 lb | Check by model and E-Nr |
| Bottom-freezer without ice maker (B11CB50SSS) | None: Bosch lists "Ice Maker: No" and ships an ice cube tray | 0 lb | None | Not applicable |
That last row matters more than it looks. If your bottom-freezer Bosch never made ice, check the spec before you troubleshoot: the B11CB50SSS has no automatic ice maker at all. Bosch sells retrofit kits only for models built “ice maker ready,” which our Bosch ice maker guide covers.
The 12 lb QuickIce Pro rating also comes with conditions. Bosch’s 500 Series manual says the maximum of up to 12 lb in 24 hours needs the freezer at its coldest setting and the ice bin emptied every 3 hours, and the footnote on Bosch’s QuickIce Pro page says the figure is based on testing with the ice bin removed. With a 3 lb bin in place and normal use, expect noticeably less.
1. Make sure ice production is actually on
This is the cause Bosch lists first, and it’s the easiest one to miss because several settings switch the ice maker off without saying so on the main display:
- Vacation mode. Bosch’s 500 and 800 Series manuals both say that while Vacation mode is activated, ice cube production is switched off (and so is the dispenser on the 500 Series). It stays on until you turn it off. On the Benchmark built-ins, Vacation mode also deactivates ice production.
- Sabbath mode. It switches off ice production and dispensing. On the French-door models it is turned on by holding “vacation” for 10 seconds and off by holding “alarm” for 5 seconds, and it ends on its own after about 80 hours. On the Benchmark built-ins you set a duration of 1 to 96 hours, and the ice maker stays off for all of it.
- The ice production setting itself. On the 800 Series it’s a button under the ice maker cover in the freezer drawer; on the 500 Series it’s lock + light, and flashing “lock” and “light” mean ice production is off. On the Benchmark it’s a Settings menu item, and on the B11CB81SSS a mechanical I/0 switch that is easy to knock to 0 while loading the freezer.
- Keylock. On the 500 Series, ice production continues while the button lock is on, but the ice and water dispenser is locked, which can look like a dead ice maker.
2. New install, or just switched on? Give it time
Bosch’s French-door manuals say ice production starts once the freezer reaches its set temperature, and the first batch is ready in about 4 hours. The 800 Series manual adds that it may take up to 48 hours to fill the ice storage container. Bosch also says to discard the ice cubes produced in the first 24 hours for hygiene reasons, so a nearly empty bin on day one is normal.
The Benchmark manual says an empty ice container takes about 24 hours to fill and says to discard the first 30-40 cubes. The B11CB81SSS bottom-freezer drops its first cubes after 2-3 hours.
To speed things up, Bosch’s own suggestion is Super freezing, which its manuals say accelerates ice cube production. On the French-door models it switches off by itself after about 8 hours. The recommended freezer setting on every model is 0°F (-18°C); the French-door models allow 6°F down to -7°F, and a warmer setting slows or stops ice. Frequent or long freezer-door openings also slow production, so check again a few hours after a busy day.
3. Check the water supply and pressure
Every Bosch manual we read sets the same water pressure window: at least 29 psi (2 bar) and no more than 116 psi (8 bar), with a pressure-reducing valve required above the maximum. Low pressure is the most common hidden cause of small cubes or slow output, and Bosch’s own troubleshooting table names the usual suspect: “the external water filter system, e.g. reverse osmosis system.” An older 800 Series manual goes further and says to install a bypass filter when a reverse osmosis system is connected.
The other water checks come straight from the same table:
- The shut-off valve feeding the fridge is fully open. Bosch requires an easy-to-reach shut-off valve on the supply, so look under the sink, in the basement below the fridge, or in an adjacent cabinet.
- The hose isn’t kinked behind the fridge, which often happens after it’s pushed back into place.
- The water is drinking-quality. Bosch says not to connect the fridge during construction work or if the water is cloudy.
4. The water filter: you can’t just pull it out
This is the Bosch-specific trap. Many owners pull a clogged filter to see whether ice comes back. On Bosch’s 500 and 800 Series French-door models, that stops the water system entirely: the manuals say the water system only works if a water filter or a bypass cap is installed. If you don’t want filtration, fit the bypass cap (Bosch part 10013297 for those models). It stays in permanently and filters out only large particles. The Benchmark built-ins work the same way with a bypass cartridge.
Bosch says to replace the filter every 6 months, or sooner when the indicator lights or ice production visibly drops. On the French-door models, reset the indicator by holding “change filter” for 3 seconds. On the 800 Series, holding the ice maker button for 3 seconds also resets the filter-change status. After any filter change, Bosch says to dispense water for 5 minutes and throw away the ice made over the next 24 hours.
Bosch UltraClarity Pro filter (BORPLFTR55 / 11032531)
- The filter Bosch names on the spec sheets for the B36CT80SNS, B36CL80ENS, B36CD50SNS, B36FD50SNS and B36BT935NS.
- Bosch says to change it every 6 months, or sooner if ice production visibly drops.
- Bosch's filter guide warns that universal filters "could have issues with properly fitting, potentially causing leaks." A filter that isn't fully seated can also cut off water to the ice maker.
Some Bosch models, including the B36IT900NP built-in, use the standard UltraClarity filter instead: Bosch lists it as 11034152 at $49.00 and under the newer retail number BORPLFTR30 at $40.00, the same filter for $9 less. Check your model’s product page before ordering.
5. The bin, the sensor and the chute
Once water is reaching the ice maker, Bosch’s documentation points to the bin:
- Bin alignment. Bosch’s US refrigerator FAQ is blunt: “make sure the ice bin is inserted and aligned correctly. If it’s not aligned properly, the ice maker won’t create ice.” The 500 Series troubleshooting table lists a bin that is “not fully inserted” as a reason the dispenser doesn’t work.
- The fill-level sensor. The ice maker stops when it detects a full bin. Bosch’s 800 Series manual says to remove all food and objects from the ice storage container, and warns against spreading the cubes out by hand. The Benchmark manual says not to store the ice scoop on the ice, because the sensor then can’t read the real fill level. On the B11CB81SSS, the fill-level gauge is a metal hook that can be blocked by a stray package.
- The ice chute. If the ice maker is making ice but nothing comes out of the dispenser, Bosch’s fix is to remove the cubes frozen together in the ice chute, “for example using a wooden spoon.” Cubes sticking together in the bin after long storage are normal, Bosch says.
If the ice tastes stale rather than missing, Bosch says to discard the remaining cubes and the ones produced over the next 24 hours, then change the water filter if it still tastes off. Our ice maker smells bad guide covers odor transfer from the freezer.
6. The Bosch reset, and what the error codes mean
Bosch doesn’t have a single reset button. Its French-door manuals give the same steps for a “fault in the ice maker”:
- Switch ice cube production off.
- Disconnect the refrigerator from power (unplug it or switch off the breaker).
- Reconnect it after 5 minutes.
- Switch ice cube production back on.
- If the fault persists, call customer service.
On the B11CB81SSS bottom-freezer, the equivalent is the I/0 switch; Bosch says to turn off the water supply for a few hours before switching the ice maker off for a long period. For how this compares with Samsung’s test button or GE’s 45-minute delay, see our how to reset an ice maker guide.
Bosch’s US error-code page covers the codes you’re likely to see:
| Display | What Bosch says it means | Bosch's fix |
|---|---|---|
| E02 | The icemaker is faulty, or the ice and water system controls have a communication issue | Reset power at the breaker for 30 seconds; call support if it isn't resolved |
| E03 | Dispenser user-interface fault | Reset power at the breaker for 30 seconds; call support if it isn't resolved |
| E or d on the temperature display | The electronics have detected a fault | Switch off for 5 minutes; call service if it returns |
| "lock" + "light" flashing (500 Series) | Ice cube production is switched off (not an error) | Switch ice production on |
The French-door manuals also describe a self-test: within 2 minutes of switching the fridge on, hold “menu” for 10 seconds. If the test ends with 5 beeps and “Er” on the display, Bosch says to call customer service.
7. When it’s a part: what Bosch charges, and what dealers charge
If the 5-minute reset doesn’t help and water is reaching the ice maker, the remaining suspects are the ice maker assembly, the water inlet valve and the control electronics. Prices below were read from each store on November 11, 2026.
| Part | Bosch US store | AppliancePartsPros | Sears PartsDirect | Reliable Parts | HNK Parts |
|---|---|---|---|---|---|
| Ice maker 12028493 (B36CT80SNS, B36CL80ENS) | $319.99, in stock | $315.95, out of stock | $284.25, back order | $330.41 sale (reg. $367.12) | $244.00, out of stock |
| Ice maker 11036056 (B36CD50SNS, B36FD50SNS) | $364.50, in stock | $346.37, in stock | $333.06, in stock | $376.35 (reg. $418.17) | $260.15, in stock |
| Water inlet valve 10005716 (B36CD50SNS, B36FD50SNS) | $44.50, in stock | $37.42, in stock | Not checked | $41.26 | Not checked |
Two details from Bosch’s own listing for the 12028493: its product name tells you to also order disassembly tool 00342180, which Bosch shows as out of stock, and Bosch lists the 11044546 as its predecessor. Model fit for each part above comes from dealer compatibility lists, so confirm against your model and E-Nr before ordering.
Labor is the bigger number. Out of warranty, Bosch’s factory service charges a $195 call-out fee plus $25 for every 6 minutes of diagnosis and labor (about $250 an hour), and the call-out and diagnosis fees are owed even if you decline the repair. A factory-installed 11036056 can therefore cost well over $600 once the part, the visit and an hour of labor are added up.
Under warranty, it’s covered. Bosch’s current US warranty statement (February 2026) covers the refrigerator for 365 days from delivery, parts and labor, and says that using third-party parts or an independent repair shop does not void the warranty. Damage caused by a non-authorized servicer is excluded unless Bosch approved it first. Bosch’s B36CD50SNS manual adds that cleaning and maintenance aren’t warranty work, so a service visit that ends with “your filter was clogged” is billable. Book through Bosch at 1-800-944-2904.
8. Recalls and reliability: what’s real and what isn’t
There is no Bosch ice maker recall. The CPSC recall database lists no recall for any Bosch or BSH Home Appliances refrigerator or ice maker; the BSH recalls it does list cover dishwashers, built-in ovens, cooktops, range hoods and Tassimo coffee makers. Bosch’s own US safety-notices page shows the same four non-refrigerator recalls. That’s a real difference from brands like Whirlpool, which has a CPSC recall tied to an ice maker wiring harness, covered in our Whirlpool ice maker not working guide.
Watch out for a fake one. A repair company’s blog describes a “CPSC #23-188” recall of Bosch French-door refrigerators over the ice maker. In the CPSC database, recall 23-188 is a children’s sleepwear recall from April 2023. If someone quotes that number to you, it isn’t a Bosch recall.
No class action either. The only legal activity that turned up is an October 2021 investigation page from the Chimicles law firm, asking Bosch owners about ice makers that don’t produce ice or freeze over. No filed class action or settlement over Bosch ice makers was found.
Ice makers are the weak spot in every brand. According to Consumer Reports’ refrigerator reliability report (updated October 15, 2026), an estimated 30% of refrigerators with icemakers have a problem by the end of the fifth year, and icemakers and water/ice dispensers are the two most commonly reported refrigerator problems across 85,290 fridges in CR members’ surveys. In other words, a Bosch ice maker that quits after a few years isn’t unusual. That matches what our ice maker not making ice guide sees across brands.
When a countertop ice maker is the cheaper fix
If your Bosch is out of warranty and the diagnosis comes back as a new ice maker plus a factory visit, the math can favor a countertop machine: a whole countertop unit costs less than the 11036056 part alone, needs no water line and makes more ice per day than any Bosch except the QuickIce Pro models. Our best countertop ice maker guide compares them. Bosch’s sibling brand Thermador has its own ice quirks, covered in our Thermador ice maker guide, and the brand-by-brand checklist lives in our ice maker troubleshooting hub.
The bottom line
Go in Bosch’s own order. Make sure ice production is on and that Vacation or Sabbath mode isn’t quietly switching it off. Reseat the ice bin, clear the fill-level sensor, and confirm the water pressure is at least 29 psi and that a filter or bypass cap is installed. Give a new install 4 hours for the first batch and up to 48 hours to fill. If it still won’t make ice, switch ice off, unplug for 5 minutes and switch it back on, or reset the breaker for 30 seconds on an E02. If the fault returns, it’s a part: $320-$365 for the ice maker at Bosch’s own prices, plus $195 and up for a factory visit once the 365-day warranty is over. And there’s no recall to claim against, whatever a blog post says about “CPSC #23-188.”
Sources: Bosch US use-and-care manuals for the B36CT80SNS (9002010794_H), B36CL80ENS (9001602135_E), B36CD50SNS (9001602137_C), B36FD50SNS (9001789176_B), B36BT935NS (8001198420_B), B36IT900NP (8001077621_H) and B11CB81SSS (8001136216_A); Bosch US product pages and spec sheets (ice output, bin size, filters); Bosch US refrigerator FAQ, refrigeration error-code page, QuickIce Pro page, repair-booking page and safety notices; Bosch US limited warranty statement 9001846064_C (Feb 2026); Bosch US parts store, AppliancePartsPros, Sears PartsDirect, Reliable Parts and HNK Parts (prices read Nov 11, 2026); CPSC recall database (BSH and Bosch recalls; recall 23-188); Chimicles law firm investigation page (Oct 29, 2021); Consumer Reports, “Most and Least Reliable Refrigerator Brands” (updated Oct 15, 2026).
Last updated: November 11, 2026.